It’s my experience that Tippa’s often suffer from a number of specific problems. On this website I deep dive into these problems and their (possible) fixes.
Note: the articles on this site apply to the Triumph-Adler Tippa model that was produced between 1964-1973 (estimated serial numbers 4369001-5689134).
October 31, 2025
If the backspace doesn’t always work, backspace plate A may not be able to reach its starting position. The most likely cause is dirt and/or hardened lubricants, especialy in area C.
Clean the involved parts. Make sure spring B pulls the plate fully back to its starting position. From there, the plate’s tooth should be able to grab the escapement rack (and pull it back) when the backspace key is pressed.
The escapement with backspace plate A and spring B (1); the plate in its starting position (2) and when pulled back (3).
A (slight) rattle during the carriage return is usually caused by a slipping silent return spring. The silent return spring is the Y-shaped leaf spring on top of the spring motor.
To test if the silent return spring is slipping, do the following:
Note: if the return still rattles during the test, the cause may be a misaligned escapement rack (rare) or a completely incorrect adjusted escapement (even rarer).
In order to silence the return, the silent return spring needs to be moved to the correct position (and stay there) by the spring motor’s rotation. Therefore it must rotate freely around the spring motor shaft, while its legs need good contact with the spring motor. Make sure all involved parts are clean and lubricate the area around the C-clip. If this doesn’t help, two things can be done:
The Y-shaped silent return spring (1), the quick fix (2) and a detached spring on its back to illustrate that the legs are bent; the long one about 1.5 mm, the short ones just a fraction (3).
If one or more key levers hit the spacebar rod that runs from left to right underneath the keyboard, the rubber spacebar bumper is likely misaligned or flattened. This will cause the spacebar to raise.
The bumper is located below the typebars and their linkages, slightly to the left. Use tools like a small screwdriver and/or tweezers to move or replace the bumper. This can be done from above and/or below. For the latter, remove the body and bottom plate to reach the bumper via the gap in the aluminium frame.
The spacebar rod (1) and the spacebar bumper (2). The spacebar lever the bumper is attached to, seen from below with the body removed; the bumper is located just below the aluminium frame (3).
For this article it is assumed the machine has already been thoroughly cleaned, but overprints still occur during normal operation. Because missing spaces are essentially overprints, this article mentions only the latter.
In most cases, overprints can be remedied by resetting the escapement trip. The trip should be as late as possible. This reduces the possibility of typebars concurrently hitting the escapement trip lever. The optimal trip point (distance between the type slug and the platen when the escapement trips) is usually around 3-4 mm.
The trip adjustment must be done for lowercase and uppercase separately; the adjustment is very precise and requires multiple test and fine tune rounds.
The adjustment of the trip can be done with set screws A and B, which are accessible from the left side of the machine when the shift lock is enabled. Move the carriage as far as possible to the right to get a good view of the screws.
Tip: make a note or photo of the current positions of the screw slots; this makes it possible to return to the original settings.
Set the screws to their “default”:
Set the trip point:
Perform an overprint test: type one or more lines alternating the letters “h” and “t” (“hththththt”). Type as fast as possible. If the test contains overprints, decrease the trip point a fraction. Repeat the process until the overprints have gone.
Caution: on most Tippa’s the outer typebars trip the escapement a little bit later than the “h” typebar. This means that if the trip point is set around 1-2 mm, the outer typebars won’t trip the escapement. This causes overprints with the outer letters only. Perform an overprint test with one of the outer letters to check for this (“hqhqhqhqhq” for example).
When de above procedure is completed, repeat it for uppercase, using the shift lock and upper screw A.
Because the set screws are concentric, they influence each other slightly. Therefore it’s needed to double check lowercase (with an overprint test) after uppercase has been adjusted, and vice versa. Most of the time some fine tuning is needed. Test and adjust until it’s possible to perform an extensive overprint test (five lines in lowercase and five in uppercase) with good results.
It is possible that even after resetting the escapement trip the occasional overprint may occur. It definitely helps to use a proper typing technique: not too fast, at a steady pace while quickly withdrawing your finger after each keystroke. The latter is especially the case with the spacebar and will help to prevent missing spaces.
Overprint tests (1); the location of the escapement trip set screws (2) and the escapement with set screws A and B and trip lever C in the “default” position (3).
The serial numbers are from The Typewriter Database, as published on January 20, 2025 (Triumph) and December 11, 2024 (Adler).
See also The Olympia Traveller Site, Laurenz’s Typewriters, The Halberg List and The Human Made and Disallow AI Signs
Site by Laurenz van Gaalen (laurenz@planet.nl)
Updated on October 31, 2025